Видео

Any reset needed on the ECM?

Remember to take the cap off the brake fluid reservoir before pressing the caliper back.

Just bought the same lights and your steps are very detailed. I have no worries about doing this fix. Thanks a million.

Great video!

I’m a Volvo man, as you know replacing wiper blades can be a pain in the a$@ for most folks, my wife got on me after months of neglecting replacing blades on her 2020 MKZ, I watched your video and it was easy as 123, the meal was superb that evening and dessert was special!!!😅😅😅 Thanks again my friend, keep making life easier for us guys!!!👍🏾

Where you get the caps

AWESOME 😊

An excellent video. Considering it’s a Corvette, it really shouldn’t come down to having to find a manual release on the floor. Why don’t they have the knobs on the windowsill like years ago?

Kewl

Thank you for a simple tutorial on this it helped a lot

Can you do a video on coolant temp sensor

Do I need an alignment after replacing my sway bar links.. because I put new ones on and my car started to sway.. it wasn't swaying before I put them and new shocks on it

Great smooth and very informative God Bless.

I need help learning how to remove the bottom trim by all 4 doors

Excellent video!! I learned the hard way Not to use Optima batteries. Let them go dead ever, and they are Junk.

Would adding a programmable time delay relay in the circuit solve the problem / eliminate the need for a switch? I used Beuler time delays on a cornering lighting circuit set to 3 seconds to smooth out trigger from turn signals flashing . I think you could program the drlay on the relay for the number of seconds the radio takes to boot up and then have the dongle do its double ground pulse at the right time.

Thank you for your advice my man!

I have the same radio and cant get anything from my rcas on the back

Great job doing mine this week .

Great video! Straight forward and repetitive phrasing to guide us who don’t have a clue 😅 thanks!

Good job dear friend.

The harmonic balancer at the end looks new. Did you swap that as well? Mine is in about the same condition as the one in the beginning of this video and I am wondering if it’s worth putting a new one in or if I should just leave it alone.

I just put a new belt on a year after I bought it and used this video as a refresher. Took it a step further and replaced the tensioner while I was in there and could not get the belt to clear the alternator how you did on installation due to the lip on the pulley. I left it loose around the tensioner instead and it slipped right on the first try!

Old video but thanks a lot. I already had my spare tire off and I literally completed the job in about 2 mins

Great video thanks for the help man

When you said God bless you all I automatically hit the thumbs up.

A shop told me needed a new front cover because that's the only way to get the seal. To change it they wanted $1200

My family has that and they like it or I don’t know if the like it

You forgot to change the sway bar bushing there the ones that go bad and creates all that clunking going down the road .Now your going to have too do it all over again to do the job the right way and replace the bushings also.

Great video. To the point. Nice set of headers on that beast.

Thanks!

Thank you sir

Best straight and to the point video ever thank you

Can you send me the info on your headlights please I have a 2010 white Denali xl and I’m loving these headlights

Good stuff very helpful

Worked for me!!

Appreciate it, this is a lifesaver!

Good video but If you're going to do the brakes right, I would replace the caliper hardware before putting new brake pads on. If you don't, built up dust and contaminated will make the caliper work harder to slide and wear out your outer pads faster than the inner pads. They make hardware for a good reason.

Quick and to the point great video….

Good explanation! Thank you.

Its worked

This was so helpful. Replaced my brakes for the first time yesthabjs to your video.i liked and subscribed. Thanks again..

Still had to wrestle with the AC belt a bit; the hoses were in the way of my sight

I would pull three bolts off the vertical legs, drill through to the side cabinet, and bolt the two together.

Good info! Thanks!

gorgeous car bro!

Do you have to use the Throttle Spray? Can I just wipe with a rag? Or any other alternatives?

Changed my Mass air flow sensor. Car engine light still on (diagnostic test only showed mass air filter) & still backfiring a little.. does if have to sit for a second

How many times should you pump the brakes?

Brother, I love your video. It is a straight and to-the-point instructional video without trying to make a Hollywood video. Keep up the work!